SA-21/06, C-11, Asapur, Varanasi, UP support@kamaldnp.com +91 8318013442
BTEUP Syllabus

Automobile Engineering — BTEUP Mechanical 5th Semester Syllabus 2026-27

KAMALDNP Raj Kamal
November 18, 2026
10 Min Read
Automobile Engineering — BTEUP Mechanical 5th Semester Syllabus 2026-27

Automobile Engineering — What This Subject Is About

These days, the automobile has become a necessity instead of a luxury — and the diploma holder in this course is required to supervise the production, repair and maintenance of vehicles. Automobile Engineering is the subject that gives you that knowledge: how a car is built, how its engine is governed and its exhaust cleaned, how power reaches the wheels through the clutch, gear box and axle, and how it is steered, suspended and stopped.

The subject has only three units: the automobile itself with fuel governing and emission control; the whole transmission system; and steering, suspension and braking. The middle unit is the biggest — the entire transmission, from clutch to tyres. It is a qualifying Open Elective-III subject: you must pass it, but its 50 internal marks are not counted in your percentage or division, and there is no external paper. The syllabus prints no unit-wise periods or marks distribution, so no weightage is claimed anywhere on this page.

Students in my class always mix up the clutch and the gear box: the clutch connects and disconnects the engine, the gear box changes the speed and torque. One is a switch, the other is a set of ratios, and the car needs both.

Subject 5.6.6 (Open Elective-III, Qualifying) • 50 Marks Internal Only • 2 Credits • L 2 – P 0 • 5th Semester — Mechanical Engineering (Production) • Session 2026–27

Note: This is one Open Elective-III option in the 5th semester. You choose ONE option: Computer Aided Design & Manufacturing, Reverse Engineering, Artificial Intelligence, Automobile Engineering, or any minimum-2-credit course (NPTEL/SWAYAM/AICTE-ELIS/C-DAC/IIT-NIT/ISRO/Tata Tech). The four taught options are linked in the Related Posts section below. Note: this is an Open Elective-III option for Production students. It is NOT the same as the Automobile sub-branch's 5.5 practicum (Automobile Maintenance, Servicing & Repair), which is a different subject with its own syllabus.
Automobile Engineering syllabus — chassis, transmission, steering, suspension and brakes, BTEUP Mechanical 5th semester 2026-27
The whole vehicle, system by system: power, transmission, steering, suspension and brakes.

What You Will Study

Unit I — Introduction to Basic Structure of an Automobile

Introduction to basic structure: automobile and its development; classification; layout of chassis; types of drives (front wheel, rear wheel, four wheel); introduction to electric and hybrid vehicles. Governing of fuel: carburetor; electronic control module (ECM, i.e. 8 bit, 16 bit and 32 bit computers); concept of double overhead cam, single overhead cam, twin cam 16 valve technology in 4 cylinder engine. Types and use of catalytic converters; selective catalytic reduction methods for emission control; emission norm standards (Bharat norms).

What an automobile is and how it is built, the three drive types, electric and hybrid vehicles, then how fuel is governed (carburetor and ECM), the valve layouts (SOHC, DOHC, 16-valve), and how the exhaust is cleaned to meet Bharat norms.

Unit II — Transmission System

Clutch: function; constructional details of single plate and multi plate friction clutches, centrifugal and semi-centrifugal clutch, cone clutch, hydraulic clutch. Gear box: function; working of sliding mesh, constant mesh and synchromesh gear box; torque converter and overdrive; introduction to automated manual transmission, automatic transmission and continuously variable transmission. Propeller shaft and rear axle: function; universal joint; differential; axles and axle drives. Wheels and tyres: types of wheels; toe in, toe out, camber, caster, kingpin inclination; wheel balancing and alignment; factors affecting tyre life.

The biggest unit: the whole transmission — clutch types, the three gear box types, torque converter and overdrive, AMT/automatic/CVT, then the propeller shaft, differential, axles, wheels and tyres with their alignment angles.

Unit III — Steering, Suspension and Braking System

Steering system; Ackerman and Davis steering gears; types of steering gears; power steering (hydraulic and electrical). Function and types of coil spring, leaf spring, air suspension, shock absorber (telescopic type). Constructional details and working of mechanical, hydraulic, air and vacuum brake; relative merits and demerits. Details of master cylinder, wheel cylinder; concept of brake drum, brake lining/pad and brake adjustment; introduction to anti-lock braking system and its working.

How the vehicle is steered (Ackerman vs Davis, power steering), how it rides (coil and leaf springs, air suspension, shock absorbers), and how it stops — the four brake types, master and wheel cylinders, and ABS.

Complete Syllabus

The full examination scheme and the reference books from the official syllabus. The unit-wise topics are in the “What You Will Study” section above. The syllabus prints no unit-wise periods and no marks-distribution table for this subject.

Examination Scheme

CodePaperTypeL – PCreditsInternalExternalTotal
5.6.6Automobile EngineeringQualifying2 – 0250—50†

Units at a Glance

UnitTopic
IIntroduction to Basic Structure of an Automobile
IITransmission System
IIISteering, Suspension and Braking System

Reference Books

As listed in the syllabus:

  • Automobile Engineering Vol I, II, Kirpal Singh, Standard Publishers Distributors, Delhi, 2012.
  • Automobile Mechanics, A.K. Babu, S.C. Sharma, Khanna Publications, New Delhi.
  • Automotive Mechanics: Principles and Practices, Joseph Heitner, East West Press.
  • Automotive Mechanics, S. Srinivasan, 2nd Edition, Tata McGraw Hill.
  • Automobile Engineering Vol I and Vol II, K. M. Gupta, Umesh Publications.
  • Automotive Engineering, Jain and Asthana, Tata McGraw Hill.
  • Website for reference: http://swayam.gov.in

How to Prepare for Automobile Engineering

Learn the clutch types and gear box types as lists. Six clutch types in the syllabus (single plate, multi plate, centrifugal, semi-centrifugal, cone, hydraulic), three gear box types (sliding mesh, constant mesh, synchromesh) — this subject rewards complete, correctly named lists.

Work the one numerical by hand. A gear pair with 20 teeth driving 60 teeth gives a ratio of 3:1: an engine speed of 3000 rpm becomes 1000 rpm at the output, and 100 Nm of engine torque becomes 300 Nm. It is the only calculation in the subject.

Give Unit II the most time. It is the biggest unit: clutch, gear box, propeller shaft, differential, wheels and tyres. Learn the differential first — it is the single most asked topic in the unit — then the four alignment angles (toe, camber, caster, kingpin inclination).

Learn Unit III as comparisons. Ackerman vs Davis, coil vs leaf spring, hydraulic vs air brakes, drum vs disc — this unit loves “compare” questions, and a two-column comparison is the fastest way to answer them.

Finish with timed practice. Work through the practice sets in one sitting of 2.30 hours, without notes — the suggested practice time. Then compare your answers with the model answer outline and note the points you missed.

Exam Tips

  • Remember it is qualifying. There is no external paper — your 50 marks come from internal assessment. Take the internal tests and assignments seriously; a fail here still means a fail, even though the marks do not count towards your division.
  • Attempt all five questions in the practice paper. The pattern gives three parts (a), (b) and (c) in each question, of which any two are to be answered — pick the two parts you know best in every question, and do not leave any question blank.
  • Do not confuse this subject with the Automobile sub-branch practicum. This is the Open Elective-III theory option for Production students; the Automobile sub-branch's 5.5 practicum (Maintenance, Servicing & Repair) is a different subject.
  • Draw where it helps. A labelled sketch of the differential, the synchromesh gear box or the hydraulic brake layout earns marks that a paragraph alone does not.
  • Do not invent weightage. The syllabus prints no unit-wise marks distribution — prepare all three units, and give Unit II the most time because it is the biggest, not because any marks split says so.

Frequently Asked Questions

Is Automobile Engineering a qualifying subject?
Yes. It is an Open Elective-III subject, assessed internally for 50 marks only, with no external examination. You must pass it, but its marks are not added to your awarded division or total marks.

Which Open Elective-III options can I choose instead?
You choose ONE option: Computer Aided Design & Manufacturing, Reverse Engineering, Artificial Intelligence, Automobile Engineering, or any minimum-2-credit course (NPTEL/SWAYAM/AICTE-ELIS/C-DAC/IIT-NIT/ISRO/Tata Tech). The four taught options are linked in the Related Posts section below.

Is this the same as the Automobile sub-branch's 5.5 practicum?
No. This is an Open Elective-III theory option (5.6.6) for Production students. The Automobile sub-branch's 5.5 practicum (Automobile Maintenance, Servicing & Repair) is a different subject with its own syllabus.

How many units are there in this subject?
Three units in the official syllabus: Introduction (structure, drives, fuel governing, emission control), Transmission, and Steering/Suspension/Braking. The notes split them into five study units so the practice paper follows the board's five-question pattern — nothing is added and nothing is dropped.

Does the syllabus give a unit-wise marks distribution?
No. The official syllabus prints no unit-wise periods and no marks-distribution table for this subject, so no weightage is claimed on this page or in the notes.

How can I download the syllabus PDF?
The PDF is free to download — use the download links in the Download section below (English and Hindi versions). It is prepared by KAMALDNP from the official BTEUP syllabus.

Related Syllabus Posts

Notes, Question Bank & Practice Sets — Automobile Engineering

The syllabus PDF on this page stays 100% FREE — no login, no payment, always. The study material below is a paid KAMALDNP product: buy once for just ₹10 and you get both the Hindi and English PDFs. Every PDF is generated with your name and enrolment number and is password-locked, so it remains personal to you. After purchase, the PDF is also sent to your email, and it is always available for download on the My Downloads page.

Short Notes (English + Hindi) — ₹10

Unit-wise short revision notes prepared from the official BTEUP 2026-27 syllabus of this subject.

Buy / Download — My Downloads
Question Bank (English + Hindi) — ₹10

One original practice (model) paper with a model-answer outline. This is a KAMALDNP practice paper — NOT a BTEUP board paper, and no question in it is promised to appear in your exam.

Buy / Download — My Downloads
Practice Sets (English + Hindi) — ₹10

10 Practice Sets — practice/guess sets only (no verified previous-year board papers available for this subject yet)

Buy / Download — My Downloads

Already purchased? You will find the Download button on the same My Downloads page — you will not be charged again.

Download the Automobile Engineering Syllabus PDF

Download the complete Automobile Engineering syllabus PDF below — prepared by KAMALDNP, with the full topic list, examination scheme and reference books.

Download the Automobile Engineering Syllabus PDF (English)

Source: BTEUP IRDT Kanpur NEP-2020 curriculum for Diploma in Mechanical Engineering (Production), effective session 2026-27, approved by the Board of Technical Education U.P. Lucknow in the C.D.C. meeting held on 16.07.2026 (urise.up.gov.in). Topic lists follow the official syllabus; short explanations are the author's own plain-English summaries, not syllabus text. Please confirm with your own polytechnic for any local changes.

Comments (0)

Share your question or experience about this syllabus. Your comment will appear after review.

No comments yet — be the first to share your thoughts!

🤖 KAMALDNP AI Assistant

Ask about courses, website & more

Hi! I'm KAMALDNP AI Assistant. Ask me about our courses, website features, or anything else! 😊
Please wait 5s...
🤖 KAMALDNP Assistant ✕

Request human callback:

🔐 Login Required
✕

Please log in to download. You will stay on this page after logging in!

New here? Register now →