SA-21/06, C-11, Asapur, Varanasi, UP support@kamaldnp.com +91 8318013442
BTEUP Syllabus

Measurements & Metrology — BTEUP Mechanical 3rd Semester Syllabus 2026-27

KAMALDNP Raj Kamal
November 18, 2026
10 Min Read
Measurements & Metrology — BTEUP Mechanical 3rd Semester Syllabus 2026-27

Measurements & Metrology — What This Subject Is About

Every machine you have ever used is made of parts that had to fit together — a shaft in a bearing, a bolt in a nut, a gear meshing with another gear. Measurements & Metrology is the subject that teaches you how to check that those parts are actually made to size. It is the science of measurement applied to the workshop: the instruments, the methods, the errors that creep in, and the modern machines — comparators, coordinate measuring machines and lasers — that keep today's factories accurate.

The subject is a practicum, which means theory and practical work go together: two lectures a week plus three practical periods, 100 marks split between a 60-mark external theory paper (3 hours) and 40 internal practical marks. The syllabus has just two units in 28 periods — linear measurements and comparators first, then angular measurements, CMM and advanced metrology — and ten practical exercises that teach you to handle the instruments yourself, from the vernier caliper to the profile projector.

Subject 3.5 (Practicum) • Total 100 Marks • 3 Credits • L 2 – P 3 • 3rd Semester — Mechanical Engineering • Session 2026–27

Note: Measurements & Metrology is a practicum subject, so its 100 marks are split between an external theory paper (60 marks, 3 hours) and internal practical assessment (40 marks). The practical exercises listed here are part of the subject itself, not a separate lab paper. The syllabus has only two units (14 periods each) — the five-question paper pattern follows the syllabus's five natural study areas: Basics of Metrology, Linear Measurements, Comparators, Angular Measurements with Screw Threads & Gears, and CMM & Advanced Metrology.
Measurements and Metrology — BTEUP Mechanical 3rd semester syllabus 2026-27: vernier caliper, micrometer and sine bar, the instruments this subject teaches
The vernier caliper, the micrometer and the sine bar — this subject teaches you to measure with them, and to trust what they tell you.

What You Will Study

Unit I — Linear Measurements and Comparators (14 Periods)

Basics of Metrology: Scope of Metrology, basic units, important terminology, Measurement — Need, Process, Role in quality control; Factors affecting measurement — SWIPE; international standardization, the Bureau of Indian Standards, important elements of measurements, methods of measurements. Precision, accuracy, factors affecting the accuracy of the measuring system, general rules for accurate measurements, precautions for use of instruments so as to avoid inaccuracy in measurements, reliability, Measurement uncertainty, systematic error and random error (compared), Selection of measuring instruments, Calibration of measuring instruments. Linear Measurements: Linear Measuring Instruments — Vernier caliper, Micrometer, Vernier height gauge, Depth Micrometer, bore gauge, Gauge blocks — Use and precautions, slip gauges. Comparator: Comparators — Working and advantages, Types — Mechanical and Pneumatic Comparators.

The foundations: what measurement is, why it matters for quality, what can go wrong with it (errors, SWIPE), and the instruments for measuring length — vernier caliper, micrometer, height gauge, bore gauge and slip gauges — plus comparators, which check parts against a standard instead of measuring them directly.

Unit II — Angular Measurements, CMM, Surface & Advanced Metrology (14 Periods)

Angular Measurements: Angular measuring instruments, Bevel protractor, Angle gauges, Precision level, Sine bar, Autocollimator. Optomechanical measurements using a measuring microscope and Profile projector. Measurement of Screw threads — Single element measurements, Pitch Diameter, Lead, Pitch. Measurement of Gears — purpose, Analytical measurement, Runout, Pitch variation, Tooth profile, Tooth thickness, Lead. Coordinate Measuring Machine: Basic concept of CMM, Types of CMM, Constructional features, Probes, Accessories, Software, Applications. Advanced Metrology: Basic concepts of lasers, types of lasers, Laser and LED based distance measuring instruments.

Angles and advanced tools: the sine bar, bevel protractor and autocollimator for angles; how screw threads and gears are measured; the coordinate measuring machine (CMM), which finds a part's shape from the coordinates of points on its surface; and lasers and LED instruments for measuring distance without touching the part.

Practical Work

  • Vernier caliper (5 hrs) — measure the dimensions of a ground MS flat / cylindrical bush using a vernier caliper; compare the results with a digital vernier caliper.
  • Outside micrometer (5 hrs) — measure the diameter of a wire using a micrometer; compare the results with a digital outside micrometer.
  • Inside micrometer (4 hrs) — measure the inside diameter of the bore of a bush / cylindrical component using an inside micrometer; compare the results with a digital inside micrometer.
  • Slip gauges (4 hrs) — measure the thickness of ground MS plates using slip gauges.
  • Vernier height gauge — measure the height of gauge blocks or parallel bars using a vernier height gauge.
  • Mechanical comparator (4 hrs) — find out the measurement of a given component and compare with a standard component using a mechanical comparator and slip gauge.

And more — the complete list of 10 practicals is inside the PDF.

How to Prepare for the Exam

This subject rewards students who practise with the instruments, not just read about them. The theory paper is 60 marks in 3 hours, and the questions follow the board's usual pattern — five questions, each with three parts, of which any two parts are to be answered in every question. The syllabus has two units, but the paper draws on five study areas: Basics of Metrology, Linear Measurements, Comparators, Angular Measurements with Screw Threads & Gears, and CMM & Advanced Metrology.

  • Master the two numericals that always matter: least count and reading of the vernier caliper and the micrometer, and the sine bar formula (sin θ = height of slip gauges ÷ distance between rollers). Practise them until the arithmetic is automatic.
  • Draw every instrument once from memory: vernier caliper, micrometer, sine bar, bevel protractor, comparator, CMM. A neat, labelled diagram is worth marks in almost every answer.
  • Learn the pairs that examiners love to compare: precision vs accuracy, systematic vs random error, mechanical vs pneumatic comparator, direct vs indirect measurement.
  • Do not skip the practicals: they carry 40 internal marks, and the viva questions come straight from them — how you wring slip gauges, how you set a sine bar, how you read a bore gauge.
  • Revise with short notes and practice papers: revise one study area at a time, write its likely questions from memory, then check yourself against the model answer outlines.

Complete Syllabus

The full examination scheme, the complete practicals list and the reference books from the official syllabus. The unit-wise topics are in the “What You Will Study” section above.

Examination Scheme

CodePaperTypeL – PCreditsInternalExternalTotal
3.5Measurements & MetrologyPracticum2 – 33Practical 40Theory 60 (3 hrs)100
Measurements & Metrology Total34060100

Units at a Glance

UnitTopicPeriodsMarks Share
1Linear Measurements and Comparators14—
2Angular Measurements, CMM, Surface & Advanced Metrology14—

Note: the official syllabus gives periods only (14 + 14 = 28); no marks-distribution table or unit weightages are given, so none are shown here.

Complete Practicals List

This is the complete list of practicals from the official syllabus.

  • Vernier caliper (5 hrs) — measure the dimensions of a ground MS flat / cylindrical bush using a vernier caliper; compare the results with a digital vernier caliper.
  • Outside micrometer (5 hrs) — measure the diameter of a wire using a micrometer; compare the results with a digital outside micrometer.
  • Inside micrometer (4 hrs) — measure the inside diameter of the bore of a bush / cylindrical component using an inside micrometer; compare the results with a digital inside micrometer.
  • Slip gauges (4 hrs) — measure the thickness of ground MS plates using slip gauges.
  • Vernier height gauge — measure the height of gauge blocks or parallel bars using a vernier height gauge.
  • Mechanical comparator (4 hrs) — find out the measurement of a given component and compare with a standard component using a mechanical comparator and slip gauge.
  • Universal bevel protractor (4 hrs) — measure the angle of a V-block / taper shank of a drill / dovetail using a universal bevel protractor.
  • Sine bar (4 hrs) — measure the angle of a machined surface using a sine bar with slip gauges.
  • Screw thread micrometer (4 hrs) — measure the geometrical dimensions of a V-thread using a screw thread micrometer.
  • Profile projector (4 hrs) — measurement of a profile using a profile projector.

Reference Books

As listed in the syllabus:

  • R. K. Jain, Engineering Metrology, 22nd Edition, Khanna Publishers, 2022.
  • N. V. Raghavendra and L. Krishnamurthy, Engineering Metrology and Measurements, Oxford University Press India, 2013.
  • R. K. Rajput, Engineering Metrology and Instrumentation, S.K. Kataria & Sons, 2nd Edition, 2013.
  • Samir Mekid, Metrology and Instrumentation: Practical Applications for Engineering and Manufacturing, John Wiley & Sons, Inc., 2021.
  • Anand K. Bewoor & Vinay A. Kulkarni, Metrology & Measurement, Tata McGraw-Hill, 2009.
  • Rega Rajendra, Principles of Engineering Metrology, Jaico Publishing House, 2008.

Frequently Asked Questions

How many marks is Measurements & Metrology worth in the 3rd semester?
100 marks in total and 3 credits: internal Practical 40 and external Theory 60 (3 hours).

How many units are there in Measurements & Metrology?
Two units, 14 periods each (28 periods in all): Unit I — Linear Measurements and Comparators; Unit II — Angular Measurements, CMM, Surface & Advanced Metrology. The official syllabus gives periods only — no marks-distribution table or unit weightages are published, so this post claims none.

Is Measurements & Metrology a theory subject or a practical subject?
It is a practicum subject (L–P 2 – 3): two lectures and three practical periods a week, with a theory paper and practical assessment together.

What practical work is there in Measurements & Metrology?
10 experiments, including vernier caliper and micrometer measurement, slip gauges, mechanical comparator, universal bevel protractor, sine bar, screw thread micrometer and profile projector. The complete list is in the Complete Syllabus section above.

Which books should I refer to for Measurements & Metrology?
The syllabus lists 6 books, including R. K. Jain, Engineering Metrology (Khanna Publishers) and R. K. Rajput, Engineering Metrology and Instrumentation (S.K. Kataria & Sons), among others. The full list is in the Complete Syllabus section above.

How can I download the Measurements & Metrology syllabus PDF?
The PDF is free to download — use the download link in the Download section below. It is prepared by KAMALDNP from the official BTEUP syllabus.

Related Syllabus Posts

Notes, Question Bank & Practice Sets — Measurements & Metrology

The syllabus PDF on this page stays 100% FREE — no login, no payment, always. The study material below is a paid KAMALDNP product: buy once for just ₹10 and you get both the Hindi and English PDFs. Every PDF is generated with your name and enrolment number and is password-locked, so it remains personal to you. After purchase, the PDF is also sent to your email, and it is always available for download on the My Downloads page.

Short Notes (English + Hindi) — ₹10

Unit-wise short revision notes prepared from the official BTEUP 2026-27 syllabus of this subject.

Buy / Download — My Downloads
Question Bank (English + Hindi) — ₹10

One original practice (model) paper with a model-answer outline. This is a KAMALDNP practice paper — NOT a BTEUP board paper, and no question in it is promised to appear in your exam.

Buy / Download — My Downloads
Practice Sets (English + Hindi) — ₹10

10 Practice Sets — practice/guess sets only (no verified previous-year board papers available for this subject yet)

Buy / Download — My Downloads

Already purchased? You will find the Download button on the same My Downloads page — you will not be charged again.

Download the Measurements & Metrology Syllabus PDF

Download the complete Measurements & Metrology syllabus PDF below — prepared by KAMALDNP, with the full topic list, practicals and reference books.

Download the Measurements & Metrology Syllabus PDF

Source: BTEUP IRDT Kanpur NEP-2020 curriculum for Diploma in Mechanical Engineering (Automobile), effective session 2025-26 (subject 3.5, pp. 22–25); the same 3rd-semester list applies to Mechanical (Production). Topic lists follow the official syllabus; short explanations are the author's own plain-English summaries, not syllabus text. Please confirm with your own polytechnic for any local changes.

Comments (0)

Share your question or experience about this syllabus. Your comment will appear after review.

No comments yet — be the first to share your thoughts!

🤖 KAMALDNP AI Assistant

Ask about courses, website & more

Hi! I'm KAMALDNP AI Assistant. Ask me about our courses, website features, or anything else! 😊
Please wait 5s...
🤖 KAMALDNP Assistant ✕

Request human callback:

🔐 Login Required
✕

Please log in to download. You will stay on this page after logging in!

New here? Register now →