SA-21/06, C-11, Asapur, Varanasi, UP support@kamaldnp.com +91 8318013442
BTEUP Syllabus

Design of Machine Elements — BTEUP Mechanical 5th Semester Syllabus 2026-27

KAMALDNP Raj Kamal
November 18, 2026
11 Min Read
Design of Machine Elements — BTEUP Mechanical 5th Semester Syllabus 2026-27

Design of Machine Elements — What This Subject Is About

Every shaft, gear, spring and bolt in a machine was sized by somebody — and if the sizing is wrong, the part fails, sometimes dangerously. Design of Machine Elements is the subject that teaches you how to size them: how thick a shaft must be to carry a torque, how many coils a spring needs, what module a gear must have, and how much load a bolted joint can safely take.

The subject covers five units in 56 periods: the introduction to design — materials, stresses and factor of safety; simple machine parts, bearings and springs; shafts, keys and couplings; the spur gear; and power screws and fasteners. The paper is a pure theory paper — 60 marks external in 3 hours, with 40 internal marks — and every unit carries the same 12 marks, so no unit can be skipped. It is the most numerical paper of the semester: almost every question ends in a calculation, and the answers are checked against standard sizes from the design data book.

Subject 5.3 (Theory) • Total 100 Marks • 4 Credits • L 4 – P 0 • 5th Semester — Mechanical Engineering • Session 2026–27

Note: The 5th-semester subjects 5.2 and 5.3 are the same for Mechanical Engineering (Production) and Mechanical Engineering (Automobile) — so this syllabus applies to both sub-branches.
Design of Machine Elements syllabus — shafts, gears, springs and fasteners, BTEUP Mechanical 5th semester 2026-27
Sized to be safe — shafts, keys, gears, springs and screws, designed so they never fail in service.

What You Will Study

Unit 1 — Introduction to Design (10 Periods, 12 Marks)

Procedure of Design, General considerations in Machine Design, Use of standards in design and preferred numbers series; Stresses; Bearing pressure Intensity; Crushing; Creep Curve; Fatigue; S-N curve; Endurance Limit; Factor of Safety and Factors governing selection of factor of Safety; Stress Concentration: Causes and Remedies; selection criteria of materials; Introduction to Theories of Failures; Ergonomics and Aesthetic consideration in design.

How a design is done step by step, what a factor of safety covers, why parts fail by fatigue and stress concentration, and how materials are chosen.

Unit 2 — Design of Simple Machine Parts; Bearings; Springs (12 Periods, 12 Marks)

Design of simple machine parts: Cotter Joint; Knuckle Joint; Design of Levers: Hand/Foot Lever and Bell Crank Lever; Design of C-Clamp; Overhang Crank. Bearings: Introduction, Types of bearing and terminology of bearings, Life Load relationship, Selection of bearings using manufacturer's catalogue. Springs: Classification and Applications of Springs; Spring terminology; Materials and Specifications; Stresses in springs; Wahl's correction factor; Deflection of springs; Energy stored in springs; Design of Helical, Tension and Compression springs subjected to uniform applied loads like I.C. engine valves, Weighing balance, Railway buffers and Governor springs; Leaf springs: Construction and Application.

Designing joints, levers, clamps and cranks; choosing a bearing from its life and load; and designing helical and leaf springs for valves, balances, buffers and governors.

Unit 3 — Design of Shafts, Keys, Couplings (10 Periods, 12 Marks)

Types of Shafts; Shaft materials; Standard Sizes; Design of Shafts (Hollow and Solid) using strength and rigidity criteria; determination of shaft diameter (Hollow and Solid), ASME code of design for shafts. Design of Sunk Keys; Effect of Keyways on strength of shaft. Introduction and function of keys, types, material and failure of keys. Design of keys (Sunk key only). Necessity, advantages and types of Couplings, Design of couplings: Muff Coupling and Flange Coupling (Protected and unprotected).

Sizing solid and hollow shafts for strength and rigidity under the ASME code, designing a sunk key for shear and crushing, and joining shafts with muff and flange couplings.

Unit 4 — Design of Spur Gear (12 Periods, 12 Marks)

Mechanical drive, classification of gears, selection of gear, involute and cycloidal profile of teeth, terminology of spur gear, standard system of gear teeth, Spur gear design considerations; Lewis equation for static beam strength of spur gear teeth; design procedure of spur gear (module determination). Power transmission capacity of spur gears in bending.

How spur gears are named and sized: module, pitch and tooth proportions, the Lewis equation for tooth strength, and how the module is chosen. (The syllabus prints 'cyloidal', a misprint for cycloidal.)

Unit 5 — Design of Power Screws and Fasteners (12 Periods, 12 Marks)

Introduction of power screw, terms used in screw threads, Thread Profiles used for power Screws; Torque required to overcome thread friction; Self-locking and overhauling property; Efficiency of power screws; Design of Screw Jack. Introduction of Fasteners, Types of Fasteners, Bolts of uniform strength, design of bolted joints, design of parallel and transverse welded joints, design of riveted joints, failure and efficiency of riveted joints, leak proofing of riveted joints: caulking and fullering.

Power screws that lift loads (the screw jack), bolts that hold parts together, welds that join them permanently, and rivets that join them with a measurable efficiency.

Complete Syllabus

The full examination scheme, the unit-wise marks distribution and the reference books from the official syllabus. The unit-wise topics are in the “What You Will Study” section above.

Examination Scheme

CodePaperTypeL – PCreditsInternalExternalTotal
5.3Design of Machine ElementsTheory4 – 04Theory 40Theory 60 (3 hrs)100
Design of Machine Elements Total44060100

Units at a Glance

UnitTopicPeriodsMarks
1Introduction to Design1012
2Design of Simple Machine Parts; Bearings; Springs1212
3Design of Shafts, Keys, Couplings1012
4Design of Spur Gear1212
5Design of Power Screws and Fasteners1212
Total5660

Every unit carries the same 12 marks in the external theory paper, as per the suggested distribution of marks in the official syllabus — so the smartest preparation gives every unit its share of time.

Reference Books

As listed in the syllabus:

  • Machine Design – Sadhu Singh, Khanna Book Publishing Co., Delhi (ISBN: 978-9382609-575).
  • Machine Design Data Book – Sadhu Singh, Revised Edition, Khanna Book Publishing Co., Delhi (ISBN: 978-9382609-513).
  • Introduction to Machine Design – V. B. Bhandari, Tata Mc-Graw Hill, New Delhi.
  • Mechanical Engineering Design – Joseph Edward Shigley, Tata Mc-Graw Hill, New Delhi.
  • Machine design – Pandya and Shah, Dhanpat Rai and Son, New Delhi.
  • Machine design – R. K. Jain, Khanna Publication, New Delhi.
  • Design Data Book – PSG Coimbatore, PSG Coimbatore.
  • Hand Book of Properties of Engineering Materials and Design Data for Machine Elements – Abdulla Shariff, Dhanpat Rai and Sons, New Delhi.

How to Prepare for Design of Machine Elements

Learn the design procedure, not just the formulas. Every design numerical follows the same steps: find the load, choose the material and its allowable stress (ultimate or yield strength divided by the factor of safety), apply the design equation, then round up to a standard size. Learn that sequence once and every unit becomes the same kind of problem.

Keep the standard sizes in mind. A shaft calculated at 63.4 mm is never made at 63.4 mm — it is made at the next standard size, 65 mm. Examiners check that you round up, never down, and that you know a standard size when you see one.

Master the two failure checks. Most parts are checked against two failures at once — a key against shear and crushing, a bolt against tension and shear, a spring against shear stress and deflection. Always do both checks; doing one and stopping is the commonest lost mark in this paper.

Learn the gear terms as a set. Module, pitch circle diameter, circular pitch, addendum, dedendum, tooth thickness — Unit 4 asks them together, and one wrong term spoils the whole numerical. Draw the tooth profile once, label every term on it, and the formulas follow.

Finish with timed practice. Work through model papers in one sitting of 3 hours, without notes — exactly like the real examination. Then compare your answers with the model answer outline and note the points you missed. Questions that repeat across sets are the subject's most important questions.

Exam Tips

  • Attempt all five questions. The paper pattern gives three parts (a), (b) and (c) in each question, of which any two are to be answered — pick the two parts you know best in every question, and do not leave any question blank.
  • Convert units before substituting. The commonest numerical mistake in this paper is mixing N/mm² with N/m², or millimetres with metres, in shaft and spring calculations. Convert first, then calculate.
  • Show every step of a numerical. Write the design equation, the substitution with units, and the answer — and state the standard size you finally select. Examiners give marks for the correct method even if the last step slips.
  • Draw neat, labelled diagrams wherever they are asked. Label every part of a coupling, a knuckle joint and a gear tooth; an unlabelled sketch earns little.
  • Manage the 3 hours. About 35 minutes per question leaves a few minutes at the end to re-read your answers. Do not spend an hour on one favourite question.
  • Write in your own words, in the same order as the questions. Short, clear points with the key terms score better than long copied paragraphs.

Frequently Asked Questions

How many marks is Design of Machine Elements worth in the 5th semester?
100 marks in total and 4 credits: internal assessment 40 marks (theory) and external theory paper 60 marks in 3 hours.

Which units carry the most marks in Design of Machine Elements?
All five units carry the same 12 marks each in the external theory paper — there is no heavy unit and no light unit. Units 2, 4 and 5 get slightly more teaching time (12 periods each) than Units 1 and 3 (10 periods each). The complete unit-wise table is in the Complete Syllabus section above.

Is Design of Machine Elements a theory subject or a practical subject?
It is a pure theory subject (L–P 4 – 0, no practical hours).

What are the most scoring topics in Design of Machine Elements?
The numericals — shaft and key problems from Unit 3, and spring and gear problems from Units 2 and 4 — are the most scoring, because a correct method earns full marks step by step. The labelled sketches (couplings, knuckle joints, gear teeth) are the next best scorers. But since every unit carries 12 marks, no unit should be left out.

Which books should I refer to for Design of Machine Elements?
The syllabus lists 8 books, including Machine Design by Sadhu Singh and Introduction to Machine Design by V. B. Bhandari, among others. The full list is in the Complete Syllabus section above.

Does this subject apply to both Mechanical sub-branches?
Yes. Subjects 5.2 and 5.3 are the same for Mechanical Engineering (Production) and Mechanical Engineering (Automobile). Only subject 5.5 differs: Production takes Advanced Manufacturing Processes, Automobile takes Automobile Maintenance Servicing & Repair.

How can I download the Design of Machine Elements syllabus PDF?
The PDF is free to download — use the download link in the Download section below. It is prepared by KAMALDNP from the official BTEUP syllabus.

Related Syllabus Posts

Notes, Question Bank & Practice Sets — Design of Machine Elements

The syllabus PDF on this page stays 100% FREE — no login, no payment, always. The study material below is a paid KAMALDNP product: buy once for just ₹10 and you get both the Hindi and English PDFs. Every PDF is generated with your name and enrolment number and is password-locked, so it remains personal to you. After purchase, the PDF is also sent to your email, and it is always available for download on the My Downloads page.

Short Notes (English + Hindi) — ₹10

Unit-wise short revision notes prepared from the official BTEUP 2026-27 syllabus of this subject.

Buy / Download — My Downloads
Question Bank (English + Hindi) — ₹10

One original practice (model) paper with a model-answer outline. This is a KAMALDNP practice paper — NOT a BTEUP board paper, and no question in it is promised to appear in your exam.

Buy / Download — My Downloads
Practice Sets (English + Hindi) — ₹10

10 Practice Sets — practice/guess sets only (no verified previous-year board papers available for this subject yet)

Buy / Download — My Downloads

Already purchased? You will find the Download button on the same My Downloads page — you will not be charged again.

Download the Design of Machine Elements Syllabus PDF

Download the complete Design of Machine Elements syllabus PDF below — prepared by KAMALDNP, with the full topic list, examination scheme and reference books.

Download the Design of Machine Elements Syllabus PDF

Source: IRDT Kanpur NEP-2020 curriculum for the Diploma in Mechanical Engineering (Production), effective session 2026-27, approved by the Board of Technical Education, U.P. Lucknow in the C.D.C. meeting held on 16.07.2026. Topic lists follow the official syllabus; short explanations are the author's own plain-English summaries, not syllabus text. Please confirm with your own polytechnic for any local changes.

Comments (0)

Share your question or experience about this syllabus. Your comment will appear after review.

No comments yet — be the first to share your thoughts!

🤖 KAMALDNP AI Assistant

Ask about courses, website & more

Hi! I'm KAMALDNP AI Assistant. Ask me about our courses, website features, or anything else! 😊
Please wait 5s...
🤖 KAMALDNP Assistant ✕

Request human callback:

🔐 Login Required
✕

Please log in to download. You will stay on this page after logging in!

New here? Register now →